# This file: stage_1.conf.default, sourced by stage_1.sh.
#
# $Id: stage_1.conf.default,v 1.2 2004/01/03 13:55:06 toor Exp toor $
# $FreeBSD: doc/en_US.ISO8859-1/articles/fbsd-from-scratch/stage_1.conf.default,v 1.4 2008/12/03 21:59:51 schweikh Exp $

# Root mount point where you create the new system. Because it is only
# used as a mount point, no space will be used on that file system as all
# files are of course written to the mounted file system(s).
DESTDIR="/newroot"

# Where your src tree is.
SRC="/usr/src"

# Where your obj is.
MAKEOBJDIRPREFIX="/usr/obj"

# Your kernel config name as from make buildkernel KERNCONF=...
KERNCONF="HAL9000"

# Your target architecture as used for make buildworld TARGET=...
# If you did not specify a TARGET when building world, it defaulted
# to the build architecture (run "uname -m" to find out if you are unsure).
TARGET="i386"  # amd64 arm i386 ia64 mips pc98 powerpc sparc64 sun4v

# Available time zones are those under /usr/share/zoneinfo.
TIMEZONE="Europe/Berlin"


#
# The create_file_systems function must create the mountpoints under
# DESTDIR, create the file systems, and then mount them under DESTDIR.
#
create_file_systems () {
  # The new root file system. Mandatory.
  # Change DEVICE names.
  DEVICE=/dev/daXYZs1a
  mkdir -m 755 -p ${DESTDIR}
  chown root:wheel ${DESTDIR}
  newfs -U ${DEVICE}
  mount -o noatime ${DEVICE} ${DESTDIR}

  # Additional file systems and initial mount points. Optional.
  DEVICE=/dev/daXYZs1e
  mkdir -m 755 -p ${DESTDIR}/var
  chown root:wheel ${DESTDIR}/var
  newfs -U ${DEVICE}
  mount -o noatime ${DEVICE} ${DESTDIR}/var

  DEVICE=/dev/daXYZs1e
  mkdir -m 755 -p ${DESTDIR}/usr
  chown root:wheel ${DESTDIR}/usr
  newfs -U ${DEVICE}
  mount -o noatime ${DEVICE} ${DESTDIR}/usr
}

#
# The create_etc_fstab function must create an fstab matching the
# file systems created in create_file_systems.
#
create_etc_fstab () {
  cat <<EOF >${DESTDIR}/etc/fstab
# Device         Mountpoint          FStype    Options              Dump Pass#
/dev/da0s1b      none                swap      sw                   0    0
/dev/da1s1b      none                swap      sw                   0    0
/dev/da2s2b      none                swap      sw                   0    0
/dev/da3s2b      none                swap      sw                   0    0
/dev/da0s1a      /                   ufs       rw,noatime           1    1
/dev/da0s1e      /var                ufs       rw,noatime           1    1
/dev/da2s1e      /usr                ufs       rw,noatime           1    1
/dev/vinum/Share /share              ufs       rw,noatime           0    2
/dev/vinum/home  /home               ufs       rw,noatime           0    2
/dev/vinum/ncvs  /home/ncvs          ufs       rw,noatime           0    2
/dev/vinum/ports /usr/ports          ufs       rw,noatime           0    2
/dev/ad1s1a      /flash              ufs       rw,noatime           0    0
/dev/ad0s1       /2k                 ntfs      ro,noauto            0    0
/dev/ad0s6       /linux              ext2fs    ro,noauto            0    0
#
/dev/cd0         /cdrom              cd9660    ro,noauto            0    0
/dev/cd1         /dvd                cd9660    ro,noauto            0    0
proc             /proc               procfs    rw                   0    0
linproc          /compat/linux/proc  linprocfs rw                   0    0
EOF
  chmod 644 ${DESTDIR}/etc/fstab
  chown root:wheel ${DESTDIR}/etc/fstab
}

#
# The copy_files function is used to copy files before mergemaster is run.
#
copy_files () {
  # Add or remove from this list at your discretion. Mostly mandatory.
  for f in \
    /.profile \
    /etc/devd.conf \
    /etc/devd.rules \
    /etc/exports \
    /etc/group \
    /etc/hosts \
    /etc/inetd.conf \
    /etc/ipfw.conf \
    /etc/make.conf \
    /etc/master.passwd \
    /etc/nsswitch.conf \
    /etc/ntp.conf \
    /etc/printcap \
    /etc/profile \
    /etc/rc.conf \
    /etc/resolv.conf \
    /etc/src.conf \
    /etc/sysctl.conf \
    /etc/ttys \
    /etc/mail/aliases \
    /etc/mail/aliases.db \
    /etc/mail/hal9000.mc \
    /etc/mail/service.switch \
    /etc/ssh/*key* \
    /etc/ssh/*_config \
    /etc/X11/xorg.conf \
    /var/cron/tabs/* \
    /root/.profile \
    /boot/*.bmp \
    /boot/loader.conf \
    /boot/device.hints ; do
    cp -p ${f} ${DESTDIR}${f}
  done
}

#
# Everything else you want to tune in the new system.
# NOTE: Do not install too many binaries here. With the old system running and
# the new binaries and headers installed you are likely to run into bootstrap
# problems. Ports should be compiled after you have booted in the new system.
#
all_remaining_customization () {
  # Without the compat symlink the linux_base files end up on the root fs:
  cd ${DESTDIR}
  mkdir -m 755 usr/compat; chown root:wheel usr/compat; ln -s usr/compat
  mkdir -m 755 usr/compat/linux;      chown root:wheel usr/compat/linux
  mkdir -m 555 usr/compat/linux/proc; chown root:wheel usr/compat/linux/proc
  mkdir -m 755 boot/grub;             chown root:wheel boot/grub
  mkdir -m 755 linux 2k;              chown root:wheel linux 2k
  mkdir -m 755 src;                   chown root:wheel src
  mkdir -m 755 share;                 chown root:wheel share
  mkdir -m 755 dvd cdrom flash;       chown root:wheel dvd cdrom flash
  mkdir -m 755 home;                  chown root:wheel home
  mkdir -m 755 usr/ports;             chown root:wheel usr/ports

  # Create the ntp and slip log files.
  touch ${DESTDIR}/var/log/ntp ${DESTDIR}/var/log/slip.log

  # Make /usr/src point to the right directory. Optional.
  # Note: some ports need part of the src tree, e.g. emulators/kqemu,
  # sysutils/lsof, sysutils/fusefs, ...
  cd ${DESTDIR}/usr
  if test "${SRC}" != /usr/src; then
    rmdir src; ln -s ${SRC}
  fi
  if test "${MAKEOBJDIRPREFIX}" != /usr/obj; then
    rmdir obj; ln -s ${MAKEOBJDIRPREFIX}
  fi

  # My personal preference is to symlink tmp -> var/tmp. Optional.
  cd ${DESTDIR}; rmdir tmp; ln -s var/tmp

  # Make spooldirs for the printers in my /etc/printcap.
  cd ${DESTDIR}/var/spool/output/lpd; mkdir -p as od ev te lp da
  touch ${DESTDIR}/var/log/lpd-errs

  # If you do not have /home on a shared partition, you may want to copy it:
  # mkdir -p ${DESTDIR}/home
  # cd /home; tar cf - . | (cd ${DESTDIR}/home; tar xpvf -)
}

# vim: tabstop=2:expandtab:shiftwidth=2:syntax=sh:
# EOF $RCSfile: stage_1.conf.default,v $