First, let us take a quick tour of the kernel build directory. All directories mentioned will be relative to the main /usr/src/sys directory, which is also accessible through the path name /sys. There are a number of subdirectories here representing different parts of the kernel, but the most important for our purposes are arch/conf, where you will edit your custom kernel configuration, and compile, which is the staging area where your kernel will be built. arch represents one of i386, alpha, amd64, ia64, powerpc, sparc64, or pc98 (an alternative development branch of PC hardware, popular in Japan). Everything inside a particular architecture's directory deals with that architecture only; the rest of the code is machine independent code common to all platforms to which FreeBSD could potentially be ported. Notice the logical organization of the directory structure, with each supported device, file system, and option in its own subdirectory.
This chapter assumes that you are using the i386 architecture in the examples. If this is not the case for your situation, make appropriate adjustments to the path names for your system's architecture.
Note: If there is not a /usr/src/sys directory on your system, then the kernel source has not been installed. The easiest way to do this is by running sysinstall as root, choosing Configure, then Distributions, then src, then base and sys. If you have an aversion to sysinstall and you have access to an “official” FreeBSD CDROM, then you can also install the source from the command line:
# mount /cdrom # mkdir -p /usr/src/sys # ln -s /usr/src/sys /sys # cat /cdrom/src/ssys.[a-d]* | tar -xzvf - # cat /cdrom/src/sbase.[a-d]* | tar -xzvf -
Next, move to the arch/conf directory and copy the GENERIC configuration file to the name you want to give your kernel. For example:
# cd /usr/src/sys/i386/conf # cp GENERIC MYKERNEL
Traditionally, this name is in all capital letters and, if you are maintaining multiple FreeBSD machines with different hardware, it is a good idea to name it after your machine's hostname. We will call it MYKERNEL for the purpose of this example.
Tip: Storing your kernel configuration file directly under /usr/src can be a bad idea. If you are experiencing problems it can be tempting to just delete /usr/src and start again. After doing this, it usually only takes a few seconds for you to realize that you have deleted your custom kernel configuration file. Also, do not edit GENERIC directly, as it may get overwritten the next time you update your source tree, and your kernel modifications will be lost.
You might want to keep your kernel configuration file elsewhere, and then create a symbolic link to the file in the i386 directory.
For example:
# cd /usr/src/sys/i386/conf # mkdir /root/kernels # cp GENERIC /root/kernels/MYKERNEL # ln -s /root/kernels/MYKERNEL
Now, edit MYKERNEL with your favorite text editor. If you are just starting out, the only editor available will probably be vi, which is too complex to explain here, but is covered well in many books in the bibliography. However, FreeBSD does offer an easier editor called ee which, if you are a beginner, should be your editor of choice. Feel free to change the comment lines at the top to reflect your configuration or the changes you have made to differentiate it from GENERIC.
If you have built a kernel under SunOS™ or some other BSD operating system, much of this file will be very familiar to you. If you are coming from some other operating system such as DOS, on the other hand, the GENERIC configuration file might seem overwhelming to you, so follow the descriptions in the Configuration File section slowly and carefully.
Note: If you sync your source tree with the latest sources of the FreeBSD project, be sure to always check the file /usr/src/UPDATING before you perform any update steps. This file describes any important issues or areas requiring special attention within the updated source code. /usr/src/UPDATING always matches your version of the FreeBSD source, and is therefore more up to date with new information than this handbook.
You must now compile the source code for the kernel.
Building a Kernel
Change to the /usr/src directory:
# cd /usr/src
Compile the kernel:
# make buildkernel KERNCONF=MYKERNEL
Install the new kernel:
# make installkernel KERNCONF=MYKERNEL
Note: It is required to have full FreeBSD source tree to build the kernel.
Tip: By default, when you build a custom kernel, all kernel modules will be rebuilt as well. If you want to update a kernel faster or to build only custom modules, you should edit /etc/make.conf before starting to build the kernel:
MODULES_OVERRIDE = linux acpi sound/sound sound/driver/ds1 ntfsThis variable sets up a list of modules to build instead of all of them.
WITHOUT_MODULES = linux acpi sound ntfsThis variable sets up a list of top level modules to exclude from the build process. For other variables which you may find useful in the process of building kernel, refer to make.conf(5) manual page.
The new kernel will be copied to the /boot/kernel directory as /boot/kernel/kernel and the old kernel will be moved to /boot/kernel.old/kernel. Now, shutdown the system and reboot to use your new kernel. If something goes wrong, there are some troubleshooting instructions at the end of this chapter that you may find useful. Be sure to read the section which explains how to recover in case your new kernel does not boot.
Note: Other files relating to the boot process, such as the boot loader(8) and configuration are stored in /boot. Third party or custom modules can be placed in /boot/kernel, although users should be aware that keeping modules in sync with the compiled kernel is very important. Modules not intended to run with the compiled kernel may result in instability or incorrectness.
This, and other documents, can be downloaded from ftp://ftp.FreeBSD.org/pub/FreeBSD/doc/.
For questions about FreeBSD, read the documentation before contacting <questions@FreeBSD.org>.
For questions about this documentation, e-mail <doc@FreeBSD.org>.